Honeywell Barcode Reader 1400g User Manual

Voyager™ 1400g Series  
Corded Area-Imaging Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com  
한글 www.honeywellaidc.com 로 이동합니다 .  
VG1400-QS Rev A  
6/12  
 
Connecting the Scanner  
USB:  
Keyboard Wedge:  
 
RS232 Serial Port:  
RS485:  
 
Reading Techniques  
The view finder projects an aiming  
beam that should be centered over the  
bar code, but it can be positioned in any  
direction for a good read.  
Hold the scanner over the bar code,  
press the button, and center the aiming  
beam on the bar code.  
The aiming beam is smaller when the  
scanner is closer to the code and larger  
when it is farther from the code. Hold  
the scanner close to smaller bar codes,  
and farther away from large bar codes  
to get a proper read.  
If the bar code is highly reflective (e.g., laminated), you may need to  
tilt the scanner at an angle so the bar code can be scanned.  
Note: PDF bar codes can only be read by Voyager models  
1400gPDF or 1400g2D and cannot be read by model  
1400g1D. 2D bar codes can only be read by Voyager model  
1400g2D and cannot be read by models 1400g1D or  
1400gPDF.  
 
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
RS485 Interface  
The RS485 interface defaults to port 5B. If you have an IBM POS  
terminal using port 9B, scan the appropriate code below to program  
the terminal, then power cycle the cash register.  
IBM Port 9B HHBCR-1  
Interface  
IBM Port 9B HHBCR-2  
Interface  
Note: For additional RS485 interface selections, see the User’s  
Guide for your product at our website,  
 
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from page 11, then the Save bar code to  
program the keyboard for your country. As a general rule, the  
following characters are not supported by the scanner for countries  
other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~.  
Program Keyboard Country  
Country Code  
Belgium  
Scan Country Code  
Scan  
1
8
2
3
4
7
Italy  
5
Denmark  
Norway  
9
Finland  
Spain  
10  
6
France  
Switzerland  
USA (Default)  
Germany/Austria  
Great Britain  
0
Save  
Note: For a complete list of country codes, see the User’s Guide for  
 
Trigger  
The following bar codes will allow you to use the scanner in Manual  
Trigger - Normal Mode (need to press the button to read) or  
Presentation mode (the scanner is activated when it “sees” a bar  
code).  
Manual Trigger - Normal  
(Default)  
Presentation Mode  
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
 
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
Function Code Transmit  
When this selection is enabled and function codes are contained  
within the scanned data, the scanner transmits the function code to  
the terminal. Charts of these function codes are provided in your  
User’s Guide. When the scanner is in keyboard wedge mode, the  
scan code is converted to a key code before it is transmitted.  
Enable  
(Default)  
Disable  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
2
4
6
1
3
5
7
 
8
9
B
D
F
A
C
E
Save  
 
EZConfig-Scanning  
To access additional features for the scanner use EZConfig-  
Scanning, an online configuration software tool, available from our  
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
Patents  
For patent information, refer to www.honeywellaidc.com/patents.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2012 Honeywell International Inc. All rights reserved.  
 
 

Grizzly Saw T10113 User Manual
Haier Air Conditioner 0010515194 User Manual
Hans Grohe Plumbing Product 06092000 User Manual
Harbor Freight Tools Nail Gun 04041 User Manual
Havis Shields Automobile Accessories KK C ST SS User Manual
Honeywell Air Cleaner F90A User Manual
Hotpoint Cooktop 60HGP User Manual
HP Hewlett Packard Welding System 6213A User Manual
Humminbird Computer Monitor 1155C User Manual
ILY Enterprise CD Player CD DVD Duplicator User Manual